- Commodity name: Center Piece Silicon Steel Cutting Line XE-ZZ-400Z
Center Piece Silicon Steel Cutting Line XE-ZZ-400Z
Product Details
I: Technical data of this equipment
1. Coil Specification
a. Applicable material: silicon steel coil
b. Quality of material: Domestic Authentic silicon steel or International Standard silicon steel
c. Material thickness:0.23-0.35mm
d. Material width:40-400mm(Max)( If the machine carries the step function, the maximum width is 365mm )
e. Coil inside diameter range:495-510mm
f. Single-head coil weight:2t
g. Motor speed: about 0-180m/min
h. Transverse shear knife material:YG11-N
i. Transverse shear knife hardness: HRA87.8
j. Transverse shear knife density:14.45g/cm³
k. Transverse shear knife bending strength3180N/ mm²
l. Installed power:14KW
2. Data of finished product
a. Sizing length:150—2500mm
b. Sizing tolerance:±0.20mm/2m during uniform speed
c. Cutting angle precision: ±0.05°
d. Cutting burr: ≤0.02mm
e. Punching burr:≤0.02mm
3. Other data of the equipment:
a. Power supply:380V/50Hz
b. Floor area (approximately): 8 m long × 2.5 m wide
c. Direction of production line: from right to left (facing the line at the console)
d. Color of equipment: pea green with faint yellow
e. Elevation of working face: about 930mm
II. Equipment Composition
1、Single head hydraulic uncoiler machine
2、Slope guide device without pit
3、Feeder machine
4、Punching & cutting machine
5、Conveyor machine
6、Pneumatic system
7、Electronic control system and console
III. Machine Profile
XE-ZZ-400Z CNC traverse cutting line of center piece silicon steel produced by Ruyi Transformer Equipments Manufacturer Co., Ltd. is the special equipment of processing transformer iron core, and can process transformer iron core equilateral step-lap core column, eccentric step-lap core column, and the eccentric angle can be adjusted.
1、Single head hydraulic uncoiler machine
1) Coil inside diameter range:495mm~510mm
2) Coil outside diameter max:1200mm
3) Uncoiler head expanding range:470~520mm
4) Coil Max width:400mm
5) Single head Max load:2t
Functional description: uncoil speed: adopt synchronization Continuously variable, synchro control with the feeder.
The speed of the uncoiler head is controlled by the feed device, feeding smoothly, no big shock.
2、Slope guide device without pit
Functional description: No pit slope buffer guide is used, consists of slope plate and detection switch.
Detection switch is installed on the Guide plate ,the change of position of the silicon steel stripe set off the detection switch release the signal to control the head feeding. can achieve the superior limit protection, The lower limit stop, normal, speed up, decelerate control.
3、Feeder machine
Roller type structure
1) This equipment consists of sizing roller, servo motor, synchronous pulley reduction gear, base frame, etc.
2) Sizing pinch roll: two pieces; the bottom roll is made of Gcr15 alloy steel which has been treated with hardening and tempering, quenching, grinding and polishing; the outer round of top roll is covered with polyurethane.
3) Control: Delta servo driver
4) Drive power: Delta servo motor together with relevant Delta drive controller
5) The lifting of top roll can be done manually.
4、Punching & cutting machine
Composition: two set of V-shape punching machine, one set of hole-punch machine
1) O-shape punching machine makes the O-shape notch by servo motor which direct drives the crank to drive the top die to move from the top to the bottom.
Punching specification φ mm( random fit one set, optional range φ10-φ24 ) Manual width modulation.
2) V-shape punching machine makes the V-shape notch by servo motor which use reduction motor to drive the crank to drive the top die to move from the top to the bottom.
V-shape punching machine has automatic width adjust motor, Step function can be realized.
5、Conveyor machine
Functional description:Conveyor is a transitional facility which is by one AC1.5 KW motor drives the conveyor belt to convey the iron core sheet to the collecting device after punching and cutting.
6、Pneumatic system
Providing power for the cylinder of the production line .
7、Electronic control system and console
1) Drive motor:
Three phase asynchronous motor: 1.5KW*1 0.5*1
Feed servo motor: AC3KW*1
V-punching machine servo motor: AC2KW*2
Stepping servo motor: EA1KE*2
Punching machine servo motor: AC2KW*1
Conveyer motor: 1.5kw*1
2) PLC full line logic control
IV. Basic engineering of mechanical equipment
1. Placed on a flat surface
2. There is no need for buffer pit between emptying device and equipment
V. List of purchased parts and main suppliers or places of origin
No. |
Purchased part |
Manufacturer or brand name |
Remarks |
1 |
Rolling bearing |
Harbin |
|
2 |
Shearing knife |
Jinfei hard alloy |
|
3 |
V-shape&O-shape punching machine |
Jinfei hard alloy |
|
4 |
Servo motor |
Delta |
|
5 |
Servo control system |
Delta |
|
6 |
Linear straight-line guide rail |
Domestic |
|
7 |
Linear ball guide rail |
Domestic |
|
8 |
Frequency converter |
Delta |
|
9 |
Pneumatic components |
AirTAC |
|
VI.After-sale service
1、We provide 1-2 installation personnel to the designated location installation and debugging. (The buyer should provide the invitation letter, visa,round-trip airfare, pay for the accommodation and meal during the period of working days. The accommodation should reach three-star standard or above,in order to ensure the safety of debugging personnel. And pay $80 per person per day as a worker’s salary.)
2、During installation and debugging, we provide free training once,The buyer should arrange the staff to cooperate actively. The training time within three days.
3、The warranty period of the machine is one year after the installation and debugging completed. during this period, we are free to repair the failure of normal use. But the buyer should provide the expenses including : visa,round-trip airfare, eating and staying during the maintenance.
Key words:
Center Piece Silicon Steel Cutting Line XE-ZZ-400Z
Logistics Shipment
Frequently Asked Questions
What materials is the equipment used to cut?
Oriented silicon steel , non-oriented silicon steel.
How many tons of silicon steel coils can the equipment withstand?
5-10 tons, we can customize according to customer requirements
What is the thickness of the silicon steel raw material coil that this equipment can cut?
0.18-0.5mm silicon steel
What is the width of the silicon steel raw material coil cut by this equipment?
40-1200mm
How much silicon steel material can this equipment cut longitudinally at one time?
According to customer requirements, the silicon steel raw material roll can be divided into up to 13.
Get A Quote
Note: Please leave your email address, our professionals will contact you as soon as possible!